Products
Categories
Hot Products
Tenlog TL-D3 Pro Independent Dual Extruder DMP 3D Printer with Touch Screen Support PVA TPU ABS PLA (600W Version) Our TL-D3 Pro Dual Extruder 3D Printer has Double Nozzles that are independent of each other, allowing it to be printed in Duplication and Mirror mode. You can also choose double different colors or materials to create at the same time. or print soluble support(such as PVA) to precisely implement models that are difficult to lay down. Thanks to the new DMP3d printing system, TL-D3 Pro gives you better creative space and double productivity! More
Tenlog TL-D5 Big Dual Filament 3D Printer Building Volume 500*mm*500mm*600mm The Tenlog TL-D5 Dual Filament 3D Printer brings a large building volume 500*mm*500mm*600mm, giving you more creative space. It has 2 Z-axis metal supporting rod to reduce a lot of sway and make the printing platform more stable during printing. More
Mini 3D Printer Enclosure, Keep Warm, Flame Retardant, Full Coverage, and a Studio, Warm Mini 4 Large Openable Windows, Touch 3D Printer from any Side, LED to Choose, Get a Studio at Same Time, Additional Front Window Insulation Layer Makes your 3D Printer Warmer, Born for the Enclosure, without any Holes, warmer and warmer... More
Max 3D Printer Enclosure, Keep Warm, Flame Retardant, Full Coverage, and a Studio, Warm Max 4 Large Openable Windows, Touch 3D Printer from any Side, LED to Choose, Get a Studio at Same Time, Additional Front Window Insulation Layer Makes your 3D Printer Warmer, Born for the Enclosure, without any Holes, warmer and warmer... More
Pro 3D Printer Enclosure, Keep Warm, Flame Retardant, Full Coverage, and a Studio, Warm Pro 4 Large Openable Windows, Touch 3D Printer from any Side, LED to Choose, Get a Studio at Same Time, Additional Front Window Insulation Layer Makes your 3D Printer Warmer, Born for the Enclosure, without any Holes, warmer and warmer... More
Tenlog Hands 2 Pro IDEX 3D Printer with Dual X Carriage Building Volume 235mm*235mm*250mm Hands 2 Pro IDEX 3D Printer, the smallest Independent Dual Extruder 3D Printer from Tenlog 3D Never Lose Hand, Powerful for Your Creation! The Really Multi Color 3D Printer! Printing good Multi Color objects. All in One Connector, collect all interfaces of extruder, hot end, temperature sensor, two fans, and break sensor. Extruder & Nozzles Kits is designed for quick disassembly and installation, very easy to change. More
DMP Motherboard with TMC2208 Driver, Work quieter and more stable. Every Tenlog DMP Motherboard need 7 pcs TMC2208 Driver. This motherboard is pre-installed with 7pcs TMC2208 drivers, and with our newest Smart DMP 3D Printing Firmware.
Brand:
TENLOGitem no.:
TL-MBTTPayment:
Click BUY NOW for The Latest PricePrice:
USD$183/Piece
The DMP motherboard contains seven TMC2208 drivers, Suitable for Hands 2, TL-D3 Pro, TL-D3S, TL-D5, TL-D6.
This kit comes with a touch screen and is equipped with a brand new UI.
Motherboard:
Input Voltage: 24V
Hot Bed Output Voltage: 24V
Support Power-loss Recover & Filament Runout Detection
SD Card Slot*1
USB Type-B Port*1
Tenlog 15Pin All-in-One Connector*2
Controllable Number of Motors: 7
Master Chip: ATmega2560
Whether to Pre-install Firmware: Yes, with Newest Version
Microcontroller
ATmega2560
Operating Voltage
5V
Input Voltage (recommended)
7-12V
Input Voltage (limit)
6-20V
Digital I/O Pins
54 (of which 15 provide PWM output)
Analog Input Pins
16
DC Current per I/O Pin
20 mA
DC Current for 3.3V Pin
50 mA
Flash Memory
256 KB of which 8 KB used by bootloader
SRAM
8 KB
EEPROM
4 KB
Clock Speed
16 MHz
LED_BUILTIN
13
Length
101.52 mm
Width
53.3 mm
Touch Screen:
4.3-inch 480*272 LCD Touch Screen OR
3.5-inch 480*320 LCD Touch Screen
Whether to Pre-install Firmware: Yes, with Newest UI
How to Upgrade Drivers to TMC2208 from A4988
1. Please make sure that the drive module and motherboard are placed in the direction shown in the figure below. Please note the direction of the screws in the red circle⭕.
2. Change the wire sequence of the total 7 motors as shown in the figure below.
Previous:
Tenlog DMP 7-axis Motherboard (Version 2) Support A4988 and TMC2208 Driver & Touch ScreenNext:
TENLOG DMP 7-axis Motherboard with Full Color Touch LCDIf you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
We have developed the DMP 3D printing system ourselves, and DMP stands for Dual Material Printing or Duplication & Mirror Printing. It can move 7-axis at the same time and has the firmware collision avoidance function of running two nozzles efficiently. Our self-developed TENLOG® Multi Nozzle 3D Printer Motherboard has a 7-axis motion control system. The Tenlog motherboard can work for 500 hours without interruption. The motherboard firmware is based on marlin 1.0.x and is open source. You can buy it to make a spare part for Tenlog Dual Extruder 3D Printer.
4.3-inch full color touch screen
Work on 24V, Maximum temperature 260℃ Nozzle diameter 0.2mm
Tenlog 3D Printer Double Head EXtruder & Nozzle Kits, also called Tenlog Quick Disassembly Replacement Nozzle Kits. Each kits requires only 4 screws to replace the entire nozzle and extruder kits.
All Tenlog Double Extrusion 3D Printers use high precision 3D printer sensors, the Photoelectric Sensors.
This is Y-axis Stoper, Y-axis just go to zero at the begin of the printing.
The ball slides slide smoothly and have a long service life and easy maintenance. Only regular grease or lubricant is required.
Work on 24V, Maximum temperature 260℃ Nozzle diameter 0.2mm
if you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Copyright © 2015-2024 Shenzhen Tenlog 3D Technology Co., Ltd.All Rights Reserved.
English
español
العربية
